• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
FIG.  9.  VERTICAL UNITS
Replacement Parts List - TM-55-1930-209-14P-7_83

TM-55-1930-209-14P-7 Water Purification Barges (NSN 1930-01-234-2165) Drinking Water System Manual
Page Navigation
  63    64    65    66    67  68  69    70    71    72    73  
INSTALLATION GUIDE & PARTS LIST HORIZONTAL AIR COMPRESSORS MODELS, 1Z785D, 1Z786D, 1Z936D, 1Z937D & 3Z271A FORM 5S1566 11122 DAYTON ELECTRIC MANUFACTURING CO. CHICAGO 60648 0577/295/5M 2 ATTENTION:  READ  CAREFULLY  AND  REFER  TO  OPERATING  MANUAL  &  SERVICE  GUIDE,  FORM  5S1408, BEFORE ATTEMPTING TO INSTALL, OPERATE OR SERVICE YOUR SPEEDAIRE PORTABLE AIR COMPRESSOR. FAILURE   TO   COMPLY   WITH   INSTRUCTIONS   COULD   RESULT   IN   PERSONAL   INJURY   AND/OR   PROPERTY DAMAGE!  RETAIN FOR FUTURE REFERENCE. Description Your  Speedaire,  Two  Stage,  Air  Compressor  is  designed  to produce compressed air up to 175 psi.  These units will give long    life    expectancy    when    used    in    industrial/commercial applications  with  a  typical  duty  cycle  of  intermittent  use,  24 hrs/days,  6-7  days  per  week.    These  compressors  feature start-stop operation:  centrifugal unloaders for loadless starts; 4 cylinder   heavy   duty   compressor   pumps;   ASME,   National Board, air receivers:  and integral frame, electric motors, built to meet or exceed NEMA specifications. General Safety.  Information CAUTION: Unit Is automatically pressure switch controlled and  may  start  unexpectedly.    Keep  hands  and  clothing away from belts, pulleys and hot surfaces.  A belt guard Is furnished as standard equipment Do riot remove the belt guard unless power Is turned off at the source. LIMITED WARRANTY Speedaire  Air  Compressors  are  warranted  by  Dayton  Electric  Mfg.  Co.  (Dayton) to  the  original  user  against  defects  in  workmanship  or  materials  under  normal use (rental use excluded), for one year after date of purchase.  Any part which is determined   to   be   defective   in   material   or   workmanship   and   returned   to   an authorized  service  location  as  Dayton  designers.    Shipping  costs  prepaid  will  be repaired  or  replaced  at  Dayton’s  option.    For  warranty  claim  procedures,  see “Prompt Disposition” below.  This warranty gives purchasers specific legal rights and purchasers may also have other rights which vary from state to state. WARRANTY  DISCLAIMER.    Dayton  has  made  a  diligent  effort  to  illustrate  and describe the products in this literature accurately; however, such illustrations and descriptions are for the sole purpose of identification, and do not express or imply a warranty that the products are merchantable, or fit for a particular purpose, or that the products will necessarily conform to the illustrations or descriptions. Except  as  provided  below,  no  warranty  or  affirmation  of  fact  express  or  implied other  than  as  stated  in  “LIMITED  WARRANTY”  above  is  made  or  authorized  by Dayton and Dayton’s liability in all events is limited to the purchase price paid. Certain  aspects  of  disclaimers  are  not  applicable  to  consumer  products;  e.g.  (a) some states do not allow the exclusion or limitation of incidental or consequential damages  sot  the  above  limitation  or  exclusion  may  not  apply  to  you;  (b)  also some   states   do   not   allow   limitations   on   how   long   an   implied   warranty   lasts consequently  the  above  limitation  may  not  apply  to  you;  and  (c)  by  law,  during the  period  of  this  Limited  Warranty,  any  implied  warranties  of  merchantability  or fitness  for  a  particular  purpose  applicable  to  consumer  products  purchased  by consumers may not be excluded or otherwise disclaimed. PROMPT   DISPOSITION   Dayton   will   make   a   good   faith   effort   for   prompt correction  or  other  adjustment  with  respect  to  any  product  which  proves  to  be defective within warranty For any product believed to be defective within warranty first  write  or  call  dealer  from  whom  product  was  purchased.    Dealer  will  give additional directions It unable to resolve satisfactorily, write to Dayton at address below  giving  dealer’s  name,  address,  date  and  number  of  dealer’s  invoice  and describing the nature of the defect.  If product was damaged in transit to you title claim with carrier DAYTON ELECTRIC MFG. CO., 5959 W. HOWARD STREET, CHICAGO, ILLINOIS 60648 Specifications and Performance COMPRESSOR PERFORMANCE AND DIMENSION DATA ASME --Motor-- Pump Free Air CFM* Overall Stock Tank Volts RPM @ Displ. at Tank PSI --Pump-- Dimensions in Inches HP No. Gal. Phase 60 HZ 175 PSI CFM 100 125 150 175 Cyl. Bore Stroke Height Width Depth 7 1/2 1Z785D 80 3 230/460 574 33.5 24.8 24.2 23.8 23.5 4 4 5/8 x 2 1/2 3 52 23 70 7 1/2 1Z935D 120 3 230/460 574 33.5 24.6 24.2 23.8 23.5 4 4 5/8 x 2 1/2 3 57 26 72 10 1Z786D 80 3 230/460 783 45.7 32.5 32.0 31.8 31.4 4 4 5/8 x 2 1/2 3 52 23 70 10 1Z937D 120 3 230/460 783 45.7 32.5 32.0 31.8 31.4 4 4 5/8 x 2 1/2 3 57 26 72 10 3Z271A 120 3 200/208 783 45.7 32.5 32.0 31.8 31.4 4 4 5/8 x 2 1/2 3 57 26 72 (*) Flow rate data determined In accordance with ASME power test codes. PUMP INFORMATION MODEL:  3Z182C, 4 5/8 & 2 1/2“ Bore x 3" Stroke, 4 Cylinder, Cast-Iron Flywheel, 19.0 O.D. Counterclockwise Rotation. PRESSURE SWITCH ADJUSTMENT WORKING  RANGE  (Large  Spring)  -  Switches  are  set  at  the  factory  to operate at the pressure indicated on the nameplate.  To raise operating pressure, turn the range spring nut down, which compresses the range spring.  Loosen the range spring nut to lower the operating pressure. DIFFERENTIAL  (Small  Spring)  Pounds  pressure  between  "Open",  and "Close" is referred to as the differential.  To increase the differential, turn down  the  differential  spring.    By  loosening  this  nut,  differential  will  be narrowed.  (Differential adjustments affect cut-out point only). Wiring diagram for pressure switch is included with the switch.  Wiring diagram for the motor is found either on the motor nameplate, or on the terminal board of the motor. When making electrical connections, unit should be grounded by means of  a  grounding  conductor,  or  by  connection  to  a  grounded,  metallic raceway electrical system. - 1 -







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.