TM 5-4610-218-20P
Code
Definition
4. Special Information.
L
Reparable item. Repair, condemnation,
a. Repair parts kits and gasket sets appear as
a n d disposal not authorized below
the last entries in the repair parts listing for the
depot/specialized repair activity level.
figure in which its parts are listed as repair
A
Item requires special handling or con-
parts.
d e m n a t i o n procedures because of
b. The following publications pertain to the
specific reasons (i.e., precious metal con-
water purification unit and its components:
tent, high dollar value, critical material
or hazardous material). Refer to ap-
TM 5-4610-218-12
O p e r a t o r and Organiza-
propriate manuals/directives for
tional Maintenance Manual
specific instructions.
c. National Stock Number. Indicates the Na-
Direct Support and General
TM 5-4610-218-34P
tional stock number assigned to the item and
Maintenance Repair Parts
which will be used for requisitioning.
a n d Special Tools Lists
d. Part Number. Indicates the primary number
(Including Depot Mainte-
used by the manufacturer (individual, company,
n a n c e Repair Parts and
firm, corporation, or Government activity), which
Special Tools List)
controls the design and characteristics of the item
by means of its engineering drawings, specifica-
Direct Support and Gen-
TM 5-4610-218-34
tions, standards, and inspection requirements to
eral Support Maintenance
identify an item or range of items.
Manual
NOTE
Depot Maintenance Work
DMWR 5-4610-218
When a stock numbered item is requisi-
Requirements
tioned, the item received may have a
different part number than the part be-
The illustrations in this manual are identical to
ing replaced.
those published in TM 5-4610-218-34P. Only
e. Federal Supply Code for Manufacturer
those parts assigned the third position SMR
(FSCM). The FSCM is a 5-digit numeric code
maintenance code "C" or "O" are listed in the
listed in SB 708-42; which is used to identify the
tabular listing; therefore, there may be a break in
manufacturer, distributor, or Government agen-
the item number sequence. Only illustrations
cy, etc.
containing organizational authorized items ap-
f. Description. Indicates the Federal item name
pear in this manual.
and, if required, a minimum description to iden-
tify the items. (Items that are included in kits
5. How to Locate Repair Parts.
and sets are listed below the name of the kit or
a. When National Stock Number or Part
set with the quantity of each item in the kit or
Number is Unknown:
set indicated in the quantity incorporated in unit
column.)
(1) Using the table of contents, determine the
assembly group within which the item belongs.
g. Unit of Measure (U/M). Indicates the stan-
This is necessary since illustrations are prepared
dard of the basic quantity of the listed item as
for assembly groups, and listings are divided in-
used in performing the actual maintenance func-
to the same groups.
t i o n . This measure is expressed by a two-
character alphabetical abbreviation (e.g., ea, in.,
(2) F i n d t h e i l l u s t r a t i o n c o v e r i n g t h e
pr, etc.). When the unit of measure differs from
assembly group to which the repair part belongs.
the unit of issue, the lowest unit of issue that
(3) Identify the repair part on the illustration
will satisfy the required units of measure will be
and note the illustration figure number and item
requisitioned.
number of the repair part.
h. Quantity Incorporated in Unit. Indicates the
(4) Using the repair parts listing, find the
quantity of the item used in the breakout shown
assembly group to which the repair part belongs
on the illustration figure, which is prepared for a
a n d locate the illustration figure and item
functional group, subfunctional group, or an
number noted on the illustration.
assembly. A "V" appearing in this column in
b. When National Stock Number or Part
lieu of a quantity indicates that no specific quan-
Number is Known.
tity is applicable (e.g., shims, spacers, etc.).
3
