TM 5-4610-218-34P
recoverability code is entered in the fifth position
f. Description. Indicates the Federal item name
of the Uniform SMR Code format as follows:
and, if required, a minimum description to identify
the items. (Items that are included in kits and sets
Recoverability
are listed below the name of the kit or set with the
Definition
Code
quantity of each item in the kit or set indicated in
Nonreparable item. When unser-
Z
the quantity incorporated in unit column.)
viceable, condemn and dispose at the
g. Unit of Measure (U/M). Indicates the stan-
level indicated in position 3.
dard of the basic quantity of the listed item as used
O
Reparable item. When uneconomically
in performing the actual maintenance function.
r e p a r a b l e , condemn and dispose at
This measure is expressed by a two-character
organizational level.
alphabetical abbreviation (e.g., ea, in., pr, etc.).
F
When the unit of measure differs from the unit of
Reparable item. When uneconomically
reparable, condemn and dispose at the
issue, the lowest unit of issue that will satisfy the
direct support level.
required units of measure will be requisitioned.
H
Reparable item. When uneconomically
h. Quantity Incorporated in Unit. Indicates the
reparable, condemn and dispose at the
quantity of the item used in the breakout shown on
general support level.
the illustration figure, which is prepared for a
functional group, s u b f u n c t i o n a l group, or an
D
Reparable item. When beyond lower
assembly. A "V" appearing in this column in lieu
level repair capability, return to depot.
of a quantity indicates that no specific quantity is
Condemnation and disposal not
applicable (e.g., shims, spacers, etc.).
authorized below depot level.
4. Special Information.
L
Reparable item. Repair, "condemnation,
a n d disposal not authorized below
a. Repair parts kits and gasket sets appear as
depot/specialized repair activity level.
the last entries in the repair parts listing for the
figure in which its parts are listed as repair
A
Item requires special handling or con-
parts.
demnation procedures because of
specific reasons (i.e., precious metal con-
b. The following publications pertain to the
tent, high dollar value, critical material
water purification unit and its components:
or hazardous material). Refer to ap-
propriate manuals/directives for
TM 5-46 10-218-12
Operator a n d Organiza-
specific instructions.
tional Maintenance Manual
c. National Stock Number. Indicates the Na-
tional stock number assigned to the item and
TM 5-46 10-218-20P
Organizational Mainte-
which will be used for requisitioning.
n a n c e Repair Parts and
Special Tools Lists
d. Part Number. Indicates the primary number
used by the manufacturer (individual, company,
Direct Support and Gen-
TM 5-4610-218-34
firm, corporation, or Government activity), which
eral Support Maintenance
controls the design and characteristics of the item
Manual
by means of its engineering drawings, specifica-
tions, standards, and inspection requirements to
DMWR 5-4610-218
Depot Maintenance Work
identify an item or range of items.
Requirements
NOTE
When a stock numbered item is requisi-
5. How to Locate Repair Parts.
tioned, the item received may have a dif-
a. When National Stock Number or Part
ferent part number than the part being
Number is Unknown:
replaced.
(1) Using the table of contents, determine the
e . Federal Supply Code for Manufacturer
assembly group within which the item belongs.
(FSCM). The FSCM is a 5-digit numeric code listed
This is necessary since illustrations are prepared
in SB 708-42; which is used to identify the
for assembly groups, and listings are divided in-
manufacturer, distributor, or Government agency,
to the same groups.
etc.
3