DO'S AND DON'TS FOR SAFE OPERATION DO'S 1. CHECK lubricant before operating the hoist. 2. EXAMINE  hoist  before  each  shift.    CHECK  for damaged  hooks  or  chains,  also  make  sure  the hoist is properly secured.  Make sure your hoist is clean and well lubricated. 3. CHECK    daily  the  chain  for  improper  seating, twisting,  kinking,  wear  or  other  defects  before twisting,  kinking,  wear  or  other  defects  before operating  the  hoist.    If  these  are  not  checked, the chain may break under a normal load. 4. BE  SURE  there  are  no  objects  in  the  way  of  a load   or   hook   when   moving   the   hoist   on   the trolley. 5. MAKE  SURE  a  load  clears  neighboring  stock piles or machinery when raising or lowering the load. 6. CENTER hoist unit over the load before lifting. 7. AVOID   swinging   of   load   or   load   hook   when traveling the hoist. 8. PROPERLY secure outdoor hoist when unattended   time   and   DO   NOT   leave   a   load unattended during 9. KEEP load block above head level when not in use. 10.    BE    SURE  the  sling  is  properly  seated  in  the saddle   of   the   hook.      Tip   loading   leads   to spreading and possible failure. DON'TS 1. NEVER lift load with hoist until all personnel are clear. 2. DO    NOT    allow  any  unqualified  personnel  to operate hoist. 3. AVOID collisions or bumping of hoists. 4. DO NOT transport load over personnel. 5. NEVER carry personnel on the hook or the load. 6. DO NOT operate hoist if you are not physically fit to do so. 7. NEVER   pick   up   a   load   beyond   the   capacity appearing on the hoist. 8. DO   NOT   tamper   with   any   parts   of   the   hoist unless you are a qualified maintenance man. 9. NEVER use the hoist chain as a sling. 10.    DO   NOT   use   chain   as   ground   for   welding. NEVER   touch   the   welding   electrode   to   the chain. 11.    DO    NOT    divert    attention    from    load    while operating hoist 12.    DO  NOT  leave  a  load  suspended  in  the  air  at the end of a work shift, or for extended periods of regular working hours. 13.    DO NOT tip or "point" load a hook. Recommended Spare Parts List for Chester Zephyr Low Head Room Plain and Geared Trolley Hoists CATALOG NO._______________ CAPACITY ________________ Quantity Part No. Description 1 C-9301 Pawl Stud 1 C-908 Pawl Snap Ring 1 C-910 Pawl Spring 1 C-923 Pawl 1 pr. C-934 Brake Discs 1 C-935 Ratchet 2 C-9329 Load Wheel only for 1-1/2, 2, 3, 4, 8, or 16-ton capacity units C-9274 C-9374 Bull Gear Shaft (Sold in combination only for 5 & 6, 10 & 12, 2 C-9390 Bull Gear 20 & 24-ton capacity units.) C-9329 Load Wheel 2 pcs. C-938-2 _______'  _______" lineal load chain 2 pcs C-38 _______'  _______" lineal load chain C-38-1/2A  or C-38-3  Required C-9203-P Plain Trolley only Depends Upon Hoist Capacity C-9203-G Geared Trolley Wheel only CHESTER HOIST DIVISION • MONOGRAM INDUSTRIES •  PHONE (216) 424-7248 • LISBON, OHIO, U.S.A.  44432 3 REPAIR PARTS ORDERING INFORMATION