TM 3-4230-237-10
0004 00
Table 1. OPERATOR'S CONTROLS AND INDICATORS - Continued
STARTINGPROCEDURE
CAUTION:Do not operate pumpdryorwhen discharge pressure is below 60 p.s.i.g.
READ THEMANUAL
1.Checkallvalve settingsbefore starting and close all circuit breakers before starting.
2.If temperature isbelow 40 degrees Fahrenheit,activateenginepre-heater for10 seconds.
3.Turn starting switch to start.
BATTEETER
VOLTM-
4.Whenenginestarts,releasestart switch to run position.
5.Checkallgages to insure properoperation.
VALVEPOSITION
6.PrimeDetergent Valve#4 must beclosed when Prime-Detergent tank is empty.
O -OPEN X- CLOSED
REMARKS
PRIME DRY PU MP
*
**
*TO TANK AGITATOR CO NNECT ON E INCH HOSE
1. TURN ON FUELSUPPLY
--
S
ON CAP O
X
X
O
**OPEN FOR 1MINUTE BEFORE STARTING, THEN
START (SEE PROCEDURE)
CLOSE TOHALFWAYFOR REMAINDER OF PRIME
OPERATION (SEE 6 ABOVE)
*
2. FILL TANK WITH WATER
1
S
ON CAP O
X
X
X
*TOAGITATOR CONNECT ONE INCH HOSE
*
3.
BLEND SLU RRY
2
T
O N CAP O
X
X
X
*TOTANK BLENDER ADD ANTISET
THEN ADD STB.
*
4.
AGITATE SLUR RY
3
T
ON CAP O
X
X
X
*TOTANK AGITATOR
DISCHARGE UPPER REEL 2,3
T
CAPC AP
O
X
O
X
5.
SLURRY
LOWER REEL 2,3
T
CAP CAP
O
O
X
X
S/
D ISC HARG E UPPER REEL 1
/T
CAP C AP
O
X
O
X
LOW W IL
LO O
6.
S/
WATER
LOWER REEL
1
/T
CAP
CAP O
O
X
X
OIL PRESSURE
S/
*
**
*FROMHEATER
D ISC HARG E UPPER REEL
1
/T
ON
ON
X
X
O
X
**TO HEATER
LIGHT
7.
S/
*
**
*FROMHEATER
H OT W TER LOWER REEL 1
A
/T
ON
ON
X
O
X
X
**TO HEATER
8.
PUMP WATER ONLY
S/
*
TO HEATER OR OTHER
1
/T
O N CAP
O
X
X
X
*TO HEATER OR OTHER
DISCHARGE FOAM
S/
*
UPPER REEL
1
/T
CAP CAP O
X
O
O
*ADJUSTFOR PRO PER BLEND
9.
OR DETERGENT
S/
M AI N
LOWER REEL 1
/T
CAP CAP O O
X
O
*ADJUST FOR PROPER BLEND
SIYSU IEM
C RC T T
10.
FLUSH SYSTEM
1
S
OPEN TANK DRAIN AND FLUSH TANK THOROUGHLY, THEN O PEN PUMP DRAIN
AND FLUSH HOSER EELS AND D ISC HARG E CONNECTIONS (SEE MANUAL)
B R EA K ER
11.
SHUTDOWN PROCEDURE
TURN START SWITCH TOOFF POSITION.
CAP ALLPIPES AND CLOSE ALL VALVES EXCEPT PUMP DRAIN VALVE.
OPEN ALLCIRCUIT BREAKERS.
IGNITISTOPITCH
ON SW
STOP
RUN
START
ENGINE
PRIR EAT
C -HUIT
EC
RETURN FUEL
FUEL OUT
PRE-HEAT
TO TANK
CIRCUT
I
TO BURNER
SWITCH
BR AKER
E
CAUTION: ENSURE PROPER
ENGAGEMENT OF QUICK
DISCONNECT COUPLINGS
18
20
19
Key
Control or Indicator
Function
Pump Unit Control Panel (Cont)
Momentary switch that activates glow plug in diesel engine. If
ENGINE PRE-HEAT SWITCH
18
temperature is below 40 F (4.44 C), press switch up to activate glow
plug.
19
Fuel hose connections
Connections for fuel hoses to and from water heater.
Controls power to glow plugs. Tripped breaker indicates short circuit
20
40 Amp PRE-HEAT CIRCUIT
in system.
BREAKER
RT
ENGINE
PRIR EAT
C -HUIT
EC
PRE-HEAT
CIRCUT
I
SWITCH
BR AKER
E
0004 00-9
