Page 16. Paragraph 27. The first sentence is changed to read:
The distributor is provided with a valve of each side of the spraybar (15 and 16, figs. 4 and 4.2).
Paragraph 28. The first sentence is changed to read:
The discharge valve (15, figs.11 and 11.1) is located beneath the operator's platform and is operated from the operator's
platform.
Paragraph 29. The first sentence is changed to read:
The suction valve (17, figs. 4 and 4.2) is located adjacent to the pump inlet tee.
Paragraph 30. The first sentence is changed to read:
The discharge pressure gage (20, figs. 4 and 4.2) is located in the discharge line.
Paragraph 31. The first sentence is changed to read:
A signal gong is provided at each end of the water tank (4, figs. 2 and 2.1).
Paragraph 32. The first sentence is changed to read:
The bitumeter assembly consists of a tachometer (1, figs. 5 and 5.1) attached to the instrument panel inside the cab of
the carrier and a drive cable (6) running from the tachometer (1) through the floorboard of the carrier cab to the frame (9,
fig. 29) of the fifth wheel, where the bitumeter drive (5) is located.
Page 17. Paragraph 34a is changed to read:
a. Turn the suction valve control lever (17, figs. 4 and 4.2) and the discharge valve control lever (15, fig.11) t OFF.
o
Paragraph 34b is changed to read:
b. Turn the spray bar valve levers (15 and 16, figs. 4 and 4.2) to OFF and perform the daily preventive maintenance
services (para. 49).
Paragraph 34j, the second sentence is changed to read:
Adjust governor control (3, figs. 11 and 11.1) for proper operating speed.
Paragraph 35a (1) is changed to read:
(1) Unlock the governor control (3, figs. 11 and 11.1) by turning it counterclockwise and push in to allow the engine
speed to decrease to an idling speed.
Paragraph 36a (2) is changed to read:
(2) Turn the suction valve control lever (17, figs.4 and 4.2) to OFF.
Paragraph 36a (3) is changed to read:
(3) Turn the discharge valve control lever (15, figs.11 and 11.10 to OFF.
Page 18. Paragraph 36b (3) is changed to read:
(3) Remove the suction cap (12, figs 4 and 42.) from the suction tee and attach the necessary length of 4-inch hose
to the suction line and tighten.
Paragraph 36b (6) is changed to read:
(6) Turn the suction valve (17, figs. 4 and 4.2) and the two spray bar control levers to OFF. Turn the discharge
valve control lever to ON.
Paragraph 36b (7). The first sentence is changed to read:
(7) Open the water tank manhole cover (1, figs. 2 and 2.1).
Paragraph 36b (10) is changed to read:
(10) Remove the suction hose (5, fig. 9) and install the cap (12, figs. 4 and 4.2) on the suction line tee (18) and
tighten securely.
Paragraph 36c (1)(a). The first sentence is changed to read:
(a) Pressure-spray. The water pump (6, figs. 4 and 4.2) pumps the water from the water tank (7) through the spray
bars (14).
Paragraph 36c (2)(a). The first sentence is changed to read:
(a) The engine governor control (3, figs.11 and 11.1) sets the engine speed, which controls pump pressure.
Page 19. Paragraph (36c(5)(c) is changed to read:
(c) Ring the signal gong (4, figs.2 and 2.1) to signal the vehicle driver to lower the bitumeter wheel assembly (12,
figs.2 and 2.1).
Paragraph 36c (5)(d) is changed to read:
(d) The truck operator will increase the speed of the carrier until the fpm (ft. per min. ) indicating pointer coincides
with the needle (7, figs.5 and 5.1).
Paragraph 36c (5)(h) is changed to read:
(h) Raise bitumeter wheel assembly with the lift rod (3, figs.5 and 5.1).
Paragraph 36c (7)(a)1 is changed to read:
1. Remove the suction cap (12, figs.4 and 4.2) from the suction tee (18).
Paragraph 36c (7)(a)2 is changed to read:
2. Remove the strainer (8, figs.33 and 33.1) from the tee (7).
Paragraph 36c (7)(a)5 is changed to read:
5. Position cap (12, figs.4 and 4.2) on the
9
