1
Screw, w/washer, 8-32 x 5/8 in.
43
Wick
2
End cap cover
44
Breaker arm
3
End cap cover gasket
45
Screw, machine 9-32 x 3/8 in.
4
Screw, w/washer, 6-32 x 3/8 in. (12 rqr)
46
Washer, flat, No. 8
5
Capacitor
47
Cam wick holder
6
Preformed packing
48
Screw, w/washer, 632 x M in.
7
Screw, machine, 8--32 x 1/2 in. (4 rqr)
49
Washer, flat, No. 6
8
Washer, lock, No. 8 (4 rqr)
50
Contact support
9
Ignition distributor cap
51
Screw, w/washer, 8-32 x 3/8 in.
10
Suppressor, insulating
52
Setscrew, --20 x 7/8 in. (2 rqr)
11
Brush
53
Magneto coil assembly
12
Spring
54
Screw, button, special
13
Electrical brush
55
Electrical clip
14
Ignition distributor rotor
56
Pin, cotter, 3/32 x 3/4 in.
15
Screw, w/washer, 6-32 x 3/8 in.
57
Nut, sleeve, special
16
Electrical wire lead terminal clip
58
Gear
17
Screw, w/washer, 10-24 x 5/8 in. (4 rqr)
59
Sleeve bearing
18
End cap
60
Woodruff Key, No. 3
19
End cap gasket
61
Spring (2 rqr)
20
Screw, machine 6-32
62
Hub assembly
21
Hood (2 rqr)
63
Spring
22
Wire fabric (2 rqr)
64
Shell
23
Wire fabric (2 rqr)
65
Baffle disk
24
Nut, pushbutton
66
Washer, flat
25
Pushbutton
67
Seal
26
Spring
68
Washer, flat, special
27
Sleeve bearing
69
Retaining ring
28
Retaining ring
70
Magneto motor
29
Primary ground tube
71
Bearing support
30
Nut, plain, hex, No. 6-32
72
Retaining ring
31
Screw, lock, No. 6
73
Washer, flat, 23/32 in.
32
Screw, machine, 6-32 x 1/2 in.
74
Bearing
33
Washer, flat No. 6
75
Screw, machine 6-32 x 5/16 in. (2 rqr)
34
Switch bushing
76
Magneto coil cover (2 rqr)
35
Lead assembly
77
Wire fabric
36
Electrical contact
78
Wire fabric (2 rqr)
37
Guide
79
Setscrew, impulse coupling pawl stop
38
Washer, flat No. 6
80
Setscrew, impulse coupling pawl stop
39
Screw, machine 6-32 x 3/8 in.
81
Retaining ring
40
Electrical clip
82
Bearing
41
Magneto coil
83
Housing
42
Retaining clip
Figure 36-Continued.
Section IV. FUEL SYSTEM, ENGINE
130. Governor
b
c. Disassembly.
(1) Press the shaft bearing (11, fig. 25) and gear (10) from the drive shaft (3) and remove the woodruff
key (21).
(2) Remove the gasket (2) from the housing (1).
(3) Remove the oil line fitting from the housing (1).
(4) Remove the cap and tachometer adapter from the housing (1).
(5) Remove the tapered pin (20) securing the yoke (13) to the shaft and lever (19).
(6) Remove the expansion plug (16) and bearing (17) from the housing (1).
(7) Slide the shaft and lever (19) out of the housing (1) and remove the preformed packing (18) and
bearing (17).
(8) Remove the drive shaft (3) and attaching assembly from the housing (1).
(9) Slide the bearing (6), yoke (13) and bearing (7) off the drive shaft (3) exterior surfaces.
(10) Remove the thrust pins (12) and slide the thrust sleeve (14) off the drive shaft (3).
(11) Remove the lockpins (9) securing the flyweights (5) to the flyweight hub(4).
AGO 6871A
79
