• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Assemble  Third  Stage  Components
HIGH PRESSURE PUMP BELT GUARD.

TM-10-4610-232-34 Water Purification Unit Reverse Osmosis 3 000 GPH Trailer Mounted Flatbed Cargo 22-1/2 Ton 8 Wheel Tandem Model No. WTA-060 Manual
Page Navigation
  253    254    255    256    257  258  259    260    261    262    263  
TM   10-4610-232-34 (6) Install four nuts (13) and washers (14) and torque to 9 to 12 ft-lbs. (8 to 15 Nm). (7) Install nozzle (12) and tube (11). (8) Install inlet valve (10) to underside of head (7) using valve key. (9) Carefully install preformed packing (9) on discharge valve (8) and install both on head (7). (10) Install head cover (6) on head (7). (11) Install stud (5), gasket (4) and nut (3). Torque to 4 ± 1 ft-lbs. (6 ± 2 Nm). (12) Install five screws (1) and extension nut (2). d.  Asssemble  External  Components: CAUTION Do not overtighten drain tube. The crankcase can crack if this is done. (1) Refer to Figure 2-79, sheet 1 and install drain tube (56), plug (59) and plug (60). (2) Install new gasket (56), tube (53) with two washers (52) and capscrews (51) and breather hose (57) (3) Install dipstick (54) and preformed packing (55). (4) Install elbow (50, Figure 2-79, sheet 2). (5)  Install  connector  (49). (6) Install adapter (48), gasket (47) and safety valve (46). (7) Install gasket (45) and connector (44). (8) Install fitting (43), connector (42) and valve (41). (9) Connect tube (39). (10) Assemble tubing(16) as follows: (a) Install capscrew (35), nuts (36), washers (37) and clamps (38). (b) Install capscrew (31), nut (32), washer (33) and clamps (34). (c) Install capscrew (27), nut (28), washer (29) and clamps (30). (d) Install capscrew (18), nut (1 9), washer (20) and clip (21) on clamp (24) and (25). (e) Install clamp (24) and (25) by installing capscrew (21), nut (22) and washer (23) and install clip (26) by installing screw (18), washer (20) and nut (19). (11) Place assembled clamps and tubing(16) on air compressor and connect tubing(16) at the points shown and secure with nuts (17) and (40). a. If they were removed, install four spring nuts (1 5, Figure 2-79, sheet 1 ) in channels (14) on the supporting posts and  secure  with  four  capscrews  (11),  Iockwashers(12)  and  washers  (13). b. Place plate (10) on channels (14) and secure with four capscrews (7), Iockwashers (8) and washers (9). c. Install spring nuts (6) and place air compressor assembly (5) on the mounting brackets welded on the plate (10). d.  Place  the  air  compressor  directly  over  the  spring  nuts  and  secure  the  air  compressor  with  capscrews  (1), Iockwashers (2) and washers (3), keeping in mind that the two shroud brackets (4) must be installed as shown on the drive sheave end of the air compressor assembly (5). 2-237







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.