TM 3-4230-237-10
0010 00
OPERATING INSTRUCTIONS ON DECALS AND INSTRUCTION PLATES - Continued
2
STARTINGPROCEDURE
CAUTON:Donotoperatepumpdryorwhendischargepressureisbelow60p.s.i.g.
I
READTHEMANUAL
1.Checkallvalvesettingsbeforestartingandcloseall circuitbreakersbeforestarting.
2.Iftemperatureisbelow40degreesFahrenheit,activateenginepre-heaterfor10seconds.
3.Turnstartingswitchtostart.
BAVOTEETER
TLTM-
4.Whenenginestarts,releasestartswitchtorunposition.
5.Checkallgagestoinsureproperoperation.
VALVEPOSITION
6.PrimeDetergentValve#4mustbeclosedwhenPrime-Detergent tankisempty.
O-OPEN X-CLOSED
REMARKS
ATOR
PRIMEDRYPUMP
*
**
*TOTANKAGITATORCONNECTONEINCHHOSE
1.
TURNONFUELSUPPLY
--
S
ON CAP O
X
X
O
**OPENFOR1MINUTEBEFORESTARTING,THEN
START(SEEPROCEDURE)
CLOSETOHALFWAYFOR REMAINDEROFPRIME
OPERATION(SEE6 ABOVE)
*
VACU-
2.
FILL TANKWITHWATER
1
S
ONCAP O
X
X
X
*TOAGITATOR CONNECTONEINCHHOSE
VACUUM GAGE
*
3.
BLENDSLURRY
2
T
ONCAP O
X
X
X
*TOTANKBLENDERADDANTISET
THENADDSTB.
*
4.
AGITATESLURRY
3
T
ONCAP O
X
X
X
*TOTANKAGITATOR
DISCHARGE UPPERREEL 2,3
T
CAPCAP
O
X
O
X
5.
SLURRY
LOWERREEL 2,3
T
CAPCAP
O
O
X
X
S/
DISCHARGE UPPER REEL 1
/T
CAPCAP
O
X
O
X
LOW W IL
LO O
6.
S/
WATER
LOWERREEL
1
/T
CAP
CAP O
O
X
X
OIL PRESSURE
S/
*
**
*FROMHEATER
DISCHARGE UPPERREEL
1
/T
ON
ON
X
X
O
X
**TOHEATER
LIGHT
7.
S/
*
**
*FROMHEATER
HOTWATER LOWER REEL 1
/T
ON
ON
X
O
X
X
**TOHEATER
8.
PUMPWATERONLY
S/
*
TOHEATEROR OTHER
1
/T
ONCAP
O
X
X
X
*TOHEATEROR OTHER
DISCHARGEFOAM
S/
*
UPPERREEL
1
/T
CAPCAP O
X
O
O
*ADJUSTFOR PROPERBLEND
9.
ORDETERGENT
S/
MAIN
LOWERREEL 1
/T
CAPCAP O O
X
O
*ADJUSTFORPROPER BLEND
SIYSUIEM
C RC TT
10.
FLUSHSYSTEM
1
S
OPENTANKDRAINANDFLUSHTANKTHOROUGHLY, THENOPENPUMPDRAIN
ANDFLUSHHOSEREELSANDDISCHARGECONNECTIONS(SEEMANUAL)
BREAKER
11. SHUTDOWNPROCEDURE
TURN STARTSWITCHTOOFFPOSITION.
CAPALLPIPESAND CLOSEALLVALVESEXCEPTPUMPDRAINVALVE.
OPEN ALLCIRCUITBREAKERS.
IGNITISTOPITCH
ON SW
STOP
RUN
START
ENGINE
PRIR EAT
C -HUIT
EC
RETURN FUEL
FUEL OUT
PRE-HEAT
TO TANK
CIRCUIT
PPESSSRE -
RREUSU
TO BURNER
SWITCH
BR AKER
E
GAGE
CLOSED
CAUTION: ENSURE PROPER
ENGAGEMENT OF QUICK
DISCONNECT COUPLINGS
Key
Plate
2
STARTING PROCEDURE Instruction Plate
STARTING PROCEDURE
CAUTION: Do not operate pump dry or when discharge pressure is below 60 p.s.i.g.
READ THE MANUAL
1. Check all valve settings before starting and close all circuit breakers before starting.
2. If temperature is below 40 degrees Fahrenheit, activate engine pre-heater for 10 seconds.
3. Turn starting switch to start.
4. When engine starts, release start switch to run position.
5. Check all gages to insure proper operation.
VALVE POSITION
6. Prime Detergent Valve #4 must be closed when Prime-Detergent tank is empty.
O - OPEN X - CLOSED
REMARKS
PRIME DRY PUMP
*
**
*TO TANK AGITATOR CONNECT ONE INCH HOSE
1. TURN ON FUEL SUPPLY
--
S
ON CAP O
X
X
O
**OPEN FOR 1 MINUTE BEFORE STARTING, THEN
START (SEE PROCEDURE)
CLOSE TO HALFWAY FOR REMAINDER OF PRIME
OPERATION (SEE 6 ABOVE)
*
2. FILL TANK WITH WATER
1
S
ON CAP O
X
X
X
*TO AGITATOR CONNECT ONE INCH HOSE
*
3.
BLEND SLURRY
2
T
ON CAP O
X
X
X
*TO TANK BLENDER ADD ANTISET
THEN ADD STB.
*
4.
AGITATE SLURRY
3
T
ON CAP O
X
X
X
*TO TANK AGITATOR
DISCHARGE UPPER REEL 2,3
T
CAP CAP O
X
O
X
5.
SLURRY
LOWER REEL 2,3
T
CAP CAP O
O
X
X
S/
DISCHARGE UPPER REEL 1
/T CAP CAP
O
X
O
X
6.
S/
WATER
LOWER REEL
1
/T CAP CAP
O
O
X
X
S/
*
**
*FROM HEATER
DISCHARGE UPPER REEL
1
/T ON ON
X
X
O
X
**TO HEATER
7.
S/ *
**
*FROM HEATER
HOT WATER LOWER REEL 1
/T ON ON
X
O
X
X
**TO HEATER
8.
PUMP WATER ONLY
S/
*
TO HEATER OR OTHER
1
/T
ON CAP
O
X
X
X
*TO HEATER OR OTHER
DISCHARGE FOAM
S/
*
UPPER REEL
1
/T
CAP CAP O
X
O
O
*ADJUST FOR PROPER BLEND
9.
OR DETERGENT
S/
LOWER REEL
1
/T
CAP CAP O O
X
O
*ADJUST FOR PROPER BLEND
10.
FLUSH SYSTEM
1
S
OPEN TANK DRAIN AND FLUSH TANK THOROUGHLY, THEN OPEN PUMP DRAIN
AND FLUSH HOSE REELS AND DISCHARGE CONNECTIONS (SEE MANUAL)
11.
SHUTDOWN PROCEDURE
TURN START SWITCH TO OFF POSITION.
CAP ALL PIPES AND CLOSE ALL VALVES EXCEPT PUMP DRAIN VALVE.
OPEN ALL CIRCUIT BREAKERS.
0010 00-2
